Archive of ‘Tutorials’ category

ERICSSON Mobile Secret Codes

ERICSSON Mobile Secret Codes

T10

*#06# for checking the IMEI (International Mobile Equipment Identity)
>*<<*<* for checking the firmware revision information (software release)
>*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language.

Shortcut for Last Dialed call menu
If you for some reason don’t want to enter the ‘Last Dialed calls menu’ by using the ‘YES’ key you can use the following key
stroke instead: First ‘0’ then ‘#’.

Access menu without Sim card
To access to the menu in your phone without having a card inside do the following: type **04*0000*0000*0000# When display say “Wrong Pin” press NO and you have access to the all menus: Info, Access, Settings, Calculator, Clock, Keylock On?, Mail, Phone book. NOTE if you try this on your phone may stop at Keylock On? menu and youĀ“ll have to take your battery out to turn the phone on again. And this will not care about Phone lock!

A way to (un)lock your cell phone on to the network(subset):
1. Press <**<
2. Then on the display appear and give you two choices: Lock to Network ? and Lock to Network subset? (Use arrow keys to select)
3. Enter the NCK number (code is provided by the SP)
4. You have 5 attemps to do this
5. Then your cell phone will work ‘only’ with the network

Warning:Ā The Service Provider (SP) Lock menu is used to lock the cell phone to the SP’s SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator. To activate/deactivate this lock one needs a special secret code that is not available to the end user. Your phone can be locked to a service provider FOREVER by doing this! If an invalid code is entered all five times, the menu will exit and be deactivated! Any further attempt to activate the NCK/NSCK lock Menu will result in the response “Not allowed”! However the NCK/NSCK lock can be recover through a direct clearing in the EEPROM.

Message Report
When you writing a message, place at the start of it the code *0# and continue with your message. It’s job is like nokias report. It gives you information about the sended message.

T18
*#06# for checking the IMEI (International Mobile Equipment Identity) Information you get from the IMEI:
XXXXXX XX XXXXXX X

TAC FAC SNR SP
TAC = Type approval code
FAC = Final assembly code
SNR = Serial number
SP = Spare

To access SIM-Locking menu of your phone, press: < * [CLR] <
Be careful or you may lock your phone.

T28
*#06# for checking the IMEI (International Mobile Equipment Identity)
>*<<*<* for checking the firmware revision information (software release)
>*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language.
>*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language.

The Service Provider (SP) Lock
The Service Provider (SP) Lock menu is used to lock the cell phone to the SP’s SIM card. Once the cell phone is locked to a specific operator, if one inserts a SIM card from a different operator the phone will refuse to accept it! The cell phone will however accept another SIM card from the same operator.

To activate/deactivate this lock one needs a special secret code that is not available to the end user. (not even to you… or is it ? in case please let me know!)

Here is how to activate the menu:
<**< Lock to Network? if pressing yes you have 5 attempts to enter NCK.
<**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK.

388
*#06# for checking the IMEI (International Mobile Equipment Identity)
*#0000# to reset the phones menu-language to English.
>*<<*<* for checking the firmware revision information (software release)
>*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language.(298 entries)
>*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language.(160 entries?)

<**< Lock to Network? if pressing yes you have 5 attempts to enter NCK.
<**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK.

GA628
*#06# for checking the IMEI (International Mobile Equipment Identity)
*#0000# to reset the phones menu-language to English.
*#103# then YES Time and date will be shown.
>*<<*<* for checking the firmware revision information (software release)
>*<<*<*> 1-row text strings. if pressing yes you can check the phones text programming in currently selected language.(298 entries)
>*<<*<*>> n-row text strings. if pressing yes you can check the phones text programming in currently selected language.(160 entries?)

Here is how to activate the menu:
<**< Lock to Network? if pressing yes you have 5 attempts to enter NCK.
<**<< Lock to Network subset? if pressing yes you have 5 attempts to enter NSCK.

Bat. level indicator when turned OFF
When the phone is turned off and the phone is not changing – the bat. level can be seen for a short period of time by pressing the ‘NO’ key quick once (it has to be quick!) and then wait for about 2 sec. The bat. level will now be shown in the display at its normal position.

Alarm Clock Menu
Go to MissedCall Empty the list Press the -> key for a second or two The option Menu size turns up Choose ‘yes’ and go from there.

An alarm clock turned up too but it never rang. I think this was because there is no clock in the phone.

Free phone calls using the GA628
This trick has only been reported working on PREPAID GSM CARDS and in some countries and with some sw versions.
The prepaid GSM SIM CARD is a kind of “SIM card” which only has a sertant amount of credit on it (like a normal phonebox telecard)… if it can be traced? – we don’t know…

Well..here’s the trick you dial the no. normally and press YES. While “connecting” is shown on the screen, the following procedure should be carried out: Press CLR then 0 then # and then NO (twice) so as to switch OFF the phone. You can then still speak on the phone while it is switched off but the SIM card does not record your calls which will lead to FREE phone calls in some countries.. we hope!!

Another variant of the code

Make a Call, while the phone says Connecting type 083# (the position 83 must be empty! ), when phone says Pos Emtpy, press the NO key and turn off the phone.

If you can make the call with the phone turned off you will face a problem when you need to hang up the phone…the only way for you to do that is remove the battery…???

 

Note:Ā The author does not take any responsibility for your actions and not responsible for any damage caused by this tutorial.

Can’t See Secured Sites?

Problem with seeing secured sites such as banks and online stores? I found this very useful to me at my teaching work.

By the way, what u need to do is create a new NOTEPAD file and write in it the following DLL’s.. just copy-paste the following lines:

regsvr32 SOFTPUB.DLL
regsvr32 WINTRUST.DLL
regsvr32 INITPKI.DLL
regsvr32 dssenh.dll
regsvr32 Rsaenh.dll
regsvr32 gpkcsp.dll
regsvr32 sccbase.dll
regsvr32 slbcsp.dll
regsvr32 Cryptdlg.dll

and save it as > all file types, and make it something like fixsecurity.bat.

Lastly, run the file that you created and nothing to worry ’bout visiting those secured websites.

Note:Ā The author does not take any responsibility for your actions and not responsible for any damage caused by this tutorial.

Motorola Mobile Secret Codes

** MOTOROLA Mobile Secret Codes **

Press menu and type one of these numbers and press OK:

11 = Status Review
13 = Available Networks
14 = Preferred Networks
22 = Select Keypad Tones
25 = Require SIM Card PIN
26 = Language Selection
32 = Repetitive Timer
33 = Single Alert Timer
34 = Set IN-Call Display
35 = Show Call Timers
36 = Show Call Charges
37 = Call Charge Settings 38 = Reset All Timers
43 = Reset All Timers
45 = Show Last Call
46 = Total For All Calls
47 = Lifetime Timer
51 = Change Unlock Code
52 = Master Reset
53 = Master Clear (Warning!! May result in deleting the Msg Editor!!!)
54 = New Security Code
55 = Automatic Lock
63 = Battery Saving Mode
Free call tip
1 Enter the phone number
2 Enter OK
3 Type *#06#
4 Press Button C
5 And finally press the button for power off.
You should now be able to talk without being billed.

The 54# Tip:
Type 1#, 2#……..54# on the keypad (when you’re not in the menu) to get the phone number used for with this key when speed dialing.

*#06# for checking the IMEI (International Mobile Equipment Identity)

(Note: pause means the * key held in until box appears)

To activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 1 [pause] [ok]
You now have to press the [MENU] and scroll to the ‘Eng Field Options’ function with the keys, and enable it.

De-activate RBS
To de-activate RBS type: [pause] [pause] [pause] 1 1 3 [pause] 0 [pause] [ok]
This only works with some versions of software.

What’s the use of RBS:
Get Distance From Base Station – Place a call, when it is answered, press [MENU] until ‘Eng Field Option’ is displayed, press [OK], select ‘Active Cell’, press [OK], press [MENU] until ‘Time Adv xxx’ appears, where xxx is a number. Multiply this number by 550, and the result is the distance from the RBS (Radio Base Station), in meters.

Get Signal Quality – press [MENU] until ‘Eng Field Option’ is displayed, press [OK], select ‘Active Cell’, press [OK], press [MENU] until ‘C1’ appears. This is the signal quality. If it becomes negative for longer than 5 seconds, a new cell is selected.

 

Note: The author does not take any responsibility for your actions and not responsible for any damage caused by this tutorial.

How do I stop my system from fscking on each reboot?

How do I stop my system from fscking on each reboot?

When you rebuild the kernel, the filesystem is marked as ‘dirty’ and so your disk will be checked with each boot. The fix is to run:
rdev -R /zImage 1

This fixes the kernel so that it is no longer convinced that the filesystem is dirty.

Note: If using lilo, then add read-only to your linux setup in your lilo config file (Usually /etc/lilo.conf)

SIEMENS Mobile Secret Codes

SIEMENS Mobile Secret Codes

C25:

SP unlock *#0003*(secret code 8 digits)#
*#0606# shows you Secret Code, but only without SIM Card.
*#06# for checking the IMEI (International Mobile Equipment Identity)
Resets language to automatic selection : * # 0000 # then Green button

Pin Out (electrical connections)

1- GND 2- SB 3- POWER 4- NC 5- TX 6- RX
7- CLOCK 8- DATA 9- GND MIC 10- HF MIC
11- AUDIO 12- GND AUDIO

Languages:
*#0000#+green phone – choose automaticaly
*#0001#+green phone – English
*#0030#+green phone – Greek
*#0031#+green phone – Netherlands
*#0032#+green phone – French
*#0034#+green phone – Spanish
*#0039#+green phone – Italian
*#0049#+green phone – German
*#0090#+green phone – Turkish

How to change PIN:
**04*old PIN*new PIN*new PIN#

How to check simlock status
*#0606# and then press left soft-key, you will see strange characters, then text (“brak blokad”). If you see for example 260-02, it means the phone is locked to Era GSM. In older models you can use *#06# and see the same information after clicking on left key (you will see IMEI and software version).

S4:

Monitor Mode – how to activate:
Press left soft-key, then 9 (SET UP) 8 (Phone Status). You will see IMEI number, then press left soft-key and in order 7684666 and red phone at the end (monitor mode has been activated). To read information from Monitor Mode – press left soft-key, then 5 (GSM SERVICE) and 6 (Monitor). Monitor mode turns off when you switch off the phone. You must activate it again if you want.

How to see date of software:
Press left soft-key, then 9 (SET UP) 8 (Phone status). You will see IMEI number, then press twice left soft-key, 98, left soft-key, 7684666, red phone (activates Monitor Mode), left soft-key, 56 (turns on Monitor Mode), left soft-key, 98, left soft-key, 7684666, hang up (red phone) >abck to “normal” and then left soft-key, 56.

S6, S8:

If you add to phonebook under ‘own phone number’ +12022243121 with namez (for example MMI), then you will see something smile.gif

S10, E10:

In phonebook enter +12022243121 as your own phone no. You will see a picture with sun, two palms and greetings.

S15e:

Monitor Mode:

Code: *#7436267*8378# (*#SIEMENS*TEST#)
Hold red phone button until it code disapears.
Menu 3.3.4 Choose frequency.
Menu 3.3.4.1 Automaticaly.
Menu 3.3.4.2 Choose GSM-900
Menu 3.3.4.3 Choose GSM-1800

Menu 10.1 MS info
Menu 10.2 Soft date
Menu 10.2.1 Software version.
Menu 10.2.2 EEProm version.
Menu 10.3 Tst and product info.
Menu 10.3.1 Handware data.
Menu 10.3.2 Date of manufacture
Menu 10.3.3 Service date
Menu 10.3.4 Date of repair.

S25:

Enhanced Full Rate
*#3370# turns on
#3370# turns off

Haft Rate Mode
*#4720# turns on
#4720# turns off.

Languages:
*#0000#+green phone – choose automaticaly
*#0001#+green phone – English
*#0030#+green phone – Greek
*#0031#+green phone – Netherlands
*#0032#+green phone – French
*#0034#+green phone – Spanish
*#0039#+green phone – Italian
*#0049#+green phone – German
*#0090#+green phone – Turkish

How to change PIN2?
**04*old PIN2*new PIN2*new PIN2#

What is my software version?
Menu 8-8-2 press left-softkey when you see IMEI number, or *#06# and then green phone button and then press left soft-key.

How to extend battery life:
IrDA – turn on only when you need.
Turn off automatic network search (6-3)Turn off Vibration alarm.

SP unlock *#0003*(secret code 8 digits)#
*#0606# shows you Secret Code, but only without SIM Card.
*#06# for checking the IMEI (International Mobile Equipment Identity)
Resets language to automatic selection : * # 0000 # then Green button

S25, M35, S35, C35

SP unlock *#0003*(secret code 8 digits)#
*#0606# shows you Secret Code, but only without SIM Card.
*#06# for checking the IMEI (International Mobile Equipment Identity)
Resets language to automatic selection : * # 0000 # then Green button

Note:Ā The author does not take any responsibility for your actions and not responsible for any damage caused by this tutorial.

1 6 7 8 9 10 13

Content Protected Using Blog Protector By: PcDrome. & GeekyCube.